Certification rules

PDF list Quality documents
RCC01 Rév. 6 Certification rules for the NF mark concerning the cut, bent, welded, spliced steels (FR)
RCC02 Rév. 4 Certification rules for the AFCAB mark concerning continuity systems (FR)
RCC03 Rév. 10 NF ABA certification rules in French
RCC03 Rév. 10 EN-FR Certification rules for the NF mark concerning the reinforcing steels (bilingual)
RCC04 Rév. 7 Certification rules for the AFCAB mark concerning the fixing of reinforcing steels (FR)
RCC05 Rév. 7 Certification rules for the AFCAB mark concerning the couplers (FR+EN)
RG AFCAB D0.1 Rév 4 General rules of the AFCAB mark
RG NF General rules of the NF mark

 

Certification procedures

PDF list Quality documents
A3 Rév.11 Sanctions, disagreement, appeals and urgent protective decisions
D0.1 Rév. 4 General rules for using the AFCAB mark (FR)
D0.5 Rév. 5 List of test houses and their capabilities (FR)
D0.7 Rév. 7 List of standards applicable for the AFCAB certifications (FR)
D0.8 Rév. 0 Impugnment of an auditor
D1.3 Rév. 3 Qualification for welding (FR)
D3.3 Rév. 9 Acceptance criteria for reinforcing steels (FR+EN)
MQ Rev14 Quality manual

 

Test procedures

PDF list Quality documents
E01 Rév. 3 Bend test to check the welding (FR)
E04 Rév. 7 Verification of the ability for straightening after bending of a reinforcing steel (FR)
E07 Rév. 7 Certification of reinforcing steels - Long term quality evaluation (FR+EN)
E08 Rév. 3 Certification of reinforcing steels : Evaluation of the quality of chemical analysis (FR)
E09 Rév. 6 Evaluation of the quality of the tests at the factory : pair comparison (FR)
E10 Rév. 2 Internal check methods when the steel is check with the fR coefficient (FR)
E11 Rév. 2 Simplified tensile test to check the welding of steels (FR)
E12 Rév. 2 Recmmendations concerning the approval of catalogues (FR)
E14 Rév. 3 Certification of cut, bent, welded steels : check of decoiling (FR)
E15.1 Rév. 2 Certification of cut, bent, welded steels : check of spot welding and qualification of welders (FR)
E15.2 Rév. 1 Certification of cut, bent, welded steels : Check of load bearing welding and qualification of welders (FR)
E16 Rév. 6 Application of EN 10080 to reinforcing steels (FR+EN)
E18 Rév. 1 Checks and tests to be performed on lattice girders
E19 Rév. 3 Debending of reinforcement in continuity sets
E20 Rév. 0 Acceptance by batches of reinforcing steels
E21 Rév. 0 Recommendations for performing internal audits
E22.1 Rév. 2 Certification of fixers : Checks applicable to load bearing weldings and qualification of welders (FR)
E22.2 Rév. 1 Certification of fixers : Checks applicable to spot welding and qualification of welders (FR)
E23 Rév. 1 Enforcement of a \"lambda\" value for the computation of fR or fP
E24 Rév. 0 Visual check of the weldings
E26 Rév. 0 Controls applicable to magnetized systems for suspended floor plates with continuity systems (LPPVE)